Uncategorized

Most Popular Cisco 300-101 Exam Online Sale

You could go through each and every Cisco 300-101 exam question and answer given in this format thoroughly, and be confident about appearing in your final Cisco 300-101 exam. Once you have gone through the entire Cisco 300-101 practice exam, you could analyze your learning with the self test engine. The Kill4exam provide two more forms of study material for Cisco 300-101 dumps. The Cisco 300-101 study guide is meant for those professionals, who do not get enough time to study. http://www.kill4exam.com/300-101.html Cisco 300-101 exam sample questions come with 80 real exam questions and answers for preparing the Cisco 300-101 Test.

QUESTION 7
Refer to the exhibit.

Which command only announces the 1.2.3.0/24 network out of FastEthernet 0/0?
A. distribute list 1 out
B. distribute list 1 out FastEthernet0/0
C. distribute list 2 out
D. distribute list 2 out FastEthernet0/0
Correct Answer: D Explanation
Explanation/Reference: http://cisco300-101dumps.hatenablog.com/
Explanation:
Access list 2 is more specific, allowing only 1.2.3.0/24, whereas access list 1 permits all 1.0.0.0/8 networks. This question also asks us to apply this distribute list
only to the outbound direction of the fast Ethernet 0/0 interface, so the correct command is “distribute list 2 out FastEthernet0/0.”

QUESTION 8
Which prefix is matched by the command ip prefix-list name permit 10.8.0.0/16 ge 24 le 24?
A. 10.9.1.0/24
B. 10.8.0.0/24
C. 10.8.0.0/16
D. 10.8.0.0/23
Correct Answer: B Explanation
Explanation/Reference:
Explanation:
With prefix lists, the ge 24 term means greater than or equal to a /24 and the le 24 means less than or equal to /24, so only a /24 is both greater than or equal to
24 and less than or equal to 24. This translate to any prefix in the 10.8.x.0/24 network, where X is any value in the 0-255 range.
Only the choice of 10.8.0.0.24 matches this.

QUESTION 9
Router A and Router B are configured with IPv6 addressing and basic routing capabilities using OSPFv3. The networks that are advertised from Router A do not show up in Router B’s routing table. After debugging IPv6 packets, the message “not a router” is found in the output. Why is the routing information not being learned by Router B?
A. OSPFv3 timers were adjusted for fast convergence.
B. The networks were not advertised properly under the OSPFv3 process.
C. An IPv6 traffic filter is blocking the networks from being learned via the Router B interface that is connected to Router A.
D. IPv6 unicast routing is not enabled on Router A or Router B.
Correct Answer: D Explanation
Explanation/Reference:
Explanation: http://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/route2.html
show ipv6 traffic Field Descriptions
Field Description
source- Number of source-routed packets.
routed
truncated Number of truncated packets.
format Errors that can result from checks performed on header fields, errors the version number, and packet length.
not a Message sent when IPv6 unicast routing is not enabled.
router

Reference:
300-101 exam

QUESTION 10
After you review the output of the command show ipv6 interface brief, you see that several IPv6 addresses have the 16-bit hexadecimal value of “FFFE” inserted into the address. Based on this information, what do you conclude about these IPv6 addresses?
A. IEEE EUI-64 was implemented when assigning IPv6 addresses on the device.
B. The addresses were misconfigured and will not function as intended.
C. IPv6 addresses containing “FFFE” indicate that the address is reserved for multicast.
D. The IPv6 universal/local flag (bit 7) was flipped.
E. IPv6 unicast forwarding was enabled, but IPv6 Cisco Express Forwarding was disabled.
Correct Answer: A Explanation
Explanation/Reference:
Explanation: Extended Unique Identifier (EUI), as per RFC2373, allows a host to assign iteslf a unique 64-Bit IP Version 6 interface identifier (EUI-64). This feature is a key benefit over IPv4 as it eliminates the need of manual configuration or DHCP as in the world of IPv4. The IPv6 EUI-64 format address is obtained through the 48-bit
MAC address. The Mac address is first separated into two 24-bits, with one being OUI (Organizationally Unique Identifier) and the other being NIC specific. The
16-bit 0xFFFE is then inserted between these two 24-bits to for the 64-bit EUI address. IEEE has chosen FFFE as a reserved value which can only appear in EUI-64 generated from the an EUI-48 MAC address.
Here is an example showing how a the Mac Address is used to generate EUI.
Next, the seventh bit from the left, or the universal/local (U/L) bit, needs to be inverted. This bit identifies whether this interface identifier is universally or locally administered. If 0, the address is locally administered and if 1, the address is globally unique. It is worth noticing that in the OUI portion, the globally unique addresses assigned by the IEEE has always been set to 0 whereas the locally created addresses has 1 configured. Therefore, when the bit is inverted, it maintains its original scope (global unique address is still global unique and vice versa). The reason for inverting can be found in RFC4291 section 2.5.1.

Once the above is done, we have a fully functional EUI-64 format address. Reference:
QUESTION 11
A packet capture log indicates that several router solicitation messages were sent from a local host on the IPv6 segment. What is the expected acknowledgment and its usage?
A. Router acknowledgment messages will be forwarded upstream, where the DHCP server will allocate addresses to the local host.
B. Routers on the IPv6 segment will respond with an advertisement that provides an external path from the local subnet, as well as certain data, such as prefix discovery.
C. Duplicate Address Detection will determine if any other local host is using the same IPv6 address for communication with the IPv6 routers on the segment.
D. All local host traffic will be redirected to the router with the lowest ICMPv6 signature, which is statically defined by the network administrator.
Correct Answer: B Explanation
Explanation/Reference:http://www.itcertlab.com/2016-download-ccna-100-101-pdf-files.html
Explanation: Router Advertisements (RA) are sent in response to router solicitation messages. Router solicitation messages, which have a value of 133 in the Type field of the ICMP packet header, are sent by hosts at system startup so that the host can immediately autoconfigure without needing to wait for the next scheduled RA message. Given that router solicitation messages are usually sent by hosts at system startup (the host does not have a configured unicast address), the source address in router solicitation messages is usually the unspecified IPv6 address (0:0:0:0:0:0:0:0). If the host has a configured unicast address, the unicast address of the interface sending the router solicitation message is used as the source address in the message. The destination address in router solicitation messages is the all-routers multicast address with a scope of the link. When an RA is sent in response to a router solicitation, the destination address in the RA message is the unicast address of the source of the router solicitation message. RA messages typically include the following information:

One or more onlink IPv6 prefixes that nodes on the local link can use to automatically configure their IPv6 addresses
Lifetime information for each prefix included in the advertisement

Sets of flags that indicate the type of autoconfiguration (stateless or stateful) that can be completed

Default router information (whether the router sending the advertisement should be used as a default router and, if so, the amount of time (in seconds) the router should be used as a default router)

Additional information for hosts, such as the hop limit and MTU a host should use in packets that it originates Reference:
QUESTION 12
You have been asked to evaluate how EIGRP is functioning in a customer network.
Traffic from R1 to R61 s Loopback address is load shared between R1-R2-R4-R6 and R1-R3- R5-R6 paths. What is the ratio of traffic over each path?
A. 1:1
B. 1:5

C. 6:8
D. 19:80 Correct Answer: D
Explanation Explanation/Reference:
Explanation:
First, find the IP address of the loopback0 interface on R6:
We see that it is 150.1.6.6, so we issue the “show ip route 150.1.6.6” command from R1 and see this:

Notice the “traffic share count” shows 19 for the first path, and 80 for the second path.
QUESTION 13
You have been asked to evaluate how EIGRP is functioning in a customer network.

As for 210-260 vce, a myriad of record checks tend to be computer-based therefore, the examinees might find out their very own exam effects soon after quality. Working with a Cisco 300-101 exam sample questions is your facts that you will be staying professional. When you order the ¬†Cisco 300-101 exam sample questions, we shall offer you free update on time for one year. Superior and also Benefit to the Cisco 300-101 pdf, 100% Assure to feed An individual’s Cisco 300-101 test Review, Downloadable, Interactive Cisco 300-101 Screening sites, Proved Answers Reviewed through Specialist, Pull and also Lose questions seeing that familiar with the very Examinations, Cisco 300-101 study materials, Process Examination Issues along with shows. Your Cisco 300-101 exam sample questions tend to be endorsed through the 100% Money-back guarantee.http://www.kill4exam.com/300-101.html